Did you know?

Purchase replacement pinch contacts and drawer full indicator (DFI) circuit boards for your Litter-Robot 3. Contact Whisker Support if your robot is still under warranty The store will not work correctly in the case when cookies are disabled. LR3 died, no power. Soo, I just replaced my insanely corroded pinch pins on my litter robot 3 that were causing the yellow flashing light. Worked for about a day or two, then it turned off and haven't been able to get it to come back on. Power adapter measured at 15 V, not hot. No heat on the button panel.Bought this and didn’t end up needing it, found out my robot had a different issue, trying to recoup some of the $ spent on it since I don’t have warranty. Litter Robot 3 LR3 DFI Kit V2 (Pinch, DFI, Housing, Screws) NEW | eBayHow to install a replacement DFI Sensor Kit and Pinch Detector Terminals in the Litter-Robot III Open Air. ... Clean your pinch detector switch contacts and glob on Vaseline the encapsulate the contact points. Litter-Robot 3: Checking the Pinch Detect. Now all it will do is flash the blue light! The drawer is empty, ...Unplug your Litter-Robot for 10 seconds and then plug it back in. This performs a hard reset. When your unit is powered back on, it will perform a Clean cycle. Once the Clean cycle is complete, the unit should go back to blue ready status. If your unit returned Home and displays a solid blue light, you've been successful. 20 votes, 18 comments. 12K subscribers in the litterrobot community. Community for all things Litter-Robot. Post your experiences, tips, tricks, and…Reassemble the globe, bonnet, and waste drawer. Plug the unit in, turn it on, and let the initial clean cycle finish. The globe should return to the Home position with the blue ready light on. If your unit does not cycle or does not cycle properly, review your installation. Purchase Litter-Robot 3 Pinch Contact & DFI Kit.Keep your automatic litter box in top shape for years to come with Litter-Robot replacement parts and refresher items. Use our DIY installation guides and videos. LR3 died, no power. Soo, I just replaced my insanely corroded pinch pins on my litter robot 3 that were causing the yellow flashing light. Worked for about a day or two, then it turned off and haven't been able to get it to come back on. Power adapter measured at 15 V, not hot. No heat on the button panel.The Litter-Robot is equipped with an Anti-Pinch safety feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly, about four times per second. Litter-Robot 4 is equipped with OmniSense™ detection that utilizes laser and weight sensor technology to provide real-time litter and waste drawer levels. OmniSense™ also supports the SafeCat system which continuously analyzes four safety zones to …Oct 13, 2021 · Hi, I have a litter robot 3 purchased on the 11-08-2020 - Order No 1036965. We have a continuos flashing yellow light (Pinch Detector Problem) I have completed the following: -. Removed the “2 metal pins” and cleaned them - not dirty and afterwords checked the continuity between them - OK. Checked the 2 magnets - OK. Cleaned the DFI sensor. Few steps: 1: Cut either the black or blue wire. 2: Get a 2k ohm resistor. (I didn't have any so I used a resistor and a potentiometer.) P.s. The litter robot sends 5v to the cat sensor and gets 0,9v back, therefore you need the 2k ohm resistor. 3: Make the pressure point where the cat sensor were placed, to a switch.As for the blue blinking light, it’s related to the DFI sensor. Let us know if you need further assistance. Sincerely, Mariagav July 5, 2023, 5:02pm 8. Hi Ebram, Thank you for the information you sent me. I still have a problem: the DFI in my litter robot 3 is longer and different than the one received with my order.

~3.5 years later and just replaced the DFI & pinch kit again, first time it was a pinch sensor issue and this time it was erroneous drawer full that cleaning the sensors was not correcting. It appears the drawer full sensors have been redesigned, hopefully for better reliability. Hey, all. About 9 months after the purchase of my litter robot 3 connect, I got the rapid yellow flash, telling me I had a fault in my pinch detector. After cleaning the metal bits failed, I ended up cutting the metal ends off and using a butt splice with an environmental seal to connect the 2 wires and bypass the pinch detector all together.Purchase replacement pinch contacts and drawer full indicator (DFI) circuit boards for your Litter-Robot 3. Contact Whisker Support if your robot is still under warranty The store will not work correctly in the case when cookies are disabled. Few steps: 1: Cut either the black or blue wire. 2: Get a 2k ohm resistor. (I didn't have any so I used a resistor and a potentiometer.) P.s. The litter robot sends 5v to the cat sensor and gets 0,9v back, therefore you need the 2k ohm resistor. 3: Make the pressure point where the cat sensor were placed, to a switch.

May 23, 2021 · How to install a replacement DFI Sensor Kit and Pinch Detector Terminals in the Litter-Robot III Open Air. Litter-Robot 3 - Base Contact Pins Designed for Litter-Robot 3 These Litter-Robot 3 - Base Contact Pins feature replacement pins for the Litter-Robot 3 Base. ... pins for the Litter-Robot 3 Base. Price: GBP 4.43. The following videos will show you how to replace these parts: Litter-Robot 3 DFI Kit + Pinch Detect Terminals Installation: Litter ...…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. The Litter-Robot 3 Open Air DFI Hardware (v2) is a replacement DFI Ha. Possible cause: Replacement anti-pinch pins, or Pinch Detectors, for Litter-Robot III Op.